Lincoln 2011 MKX User Manual

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 18Entertainment Systems 35MyLincoln Touch™ system 35Climate Con

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

Note: The doors will not autounlock if the vehicle has beenelectronically locked before the driver door is opened.Deactivating/activating autounlock f

Keyless entry keypad autounlock enable/disable procedure1. Turn the ignition off.2. Close all the doors.3. Enter factory–set 5–digit entrycode.4. Pres

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment.The typ

Your intelligent access system uses a radio frequency (RF) signal tocommunicate with your vehicle and authorize your vehicle to unlockwhen commanded (

The battery saver feature will turn off the lamps 10 minutes after theignition is turned off.Two stage unlocking may be disabled or re-enabled by simu

If the liftgate stops mid-travel, it may have detected an obstacle. Checkto ensure the liftgate swing zone is free from obstruction and reset thepower

2. Within three seconds press the .3. Repeat this procedure for transmitter if desired.Memory profilesThe memory feature also coordinates with user-cr

Replacing lost intelligent access keys (IA keys)If you would like to have your IA keys reprogrammed because you lostone, or would like to buy addition

• If the dome lamps were turned on using the panel dimmer control, thebattery saver will shut them off 10 minutes after the ignition has beenturned of

The remote start system will not work if:• The ignition is on.• The alarm system is triggered.• The feature has been disabled.• The hood is not closed

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

The ignition must be turned on and then back off or allow one hour topass before using remote start again.Turning the engine off after using remote st

Tips:• Do not set a code that uses five of the same number.• Do not use five numbers in sequential order.• The factory set code will work even if you

SECURILOCK姞 PASSIVE ANTI-THEFT SYSTEMSecuriLock威 passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent

If your intelligent access key are lost or stolen and you don’t have anextra key, you will need to have your vehicle towed to an authorizeddealer. The

been programmed to your vehicle, you cannot program anymore and themessage MAX # OF KEYS LEARNED will be displayed on the messagecenter.7. Remove inte

After locking the doors using any of the methods above, the turn signallamps will flash once indicating that the perimeter alarm is in thepre-armed mo

FRONT SEATINGWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the e

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front power seatWARNING:

WARNING LIGHTS AND CHIMESInstrument cluster with standard measure shown; metric similarWarning lights can alert you to a vehicle condition that may be

Press the front or rear portion to tiltthe seat.Press the control to move the seatforward, backward, up or down.Move the switch to recline theseatback

Heated and cooled seatsHeated seatsWARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal

If the engine falls below 350 RPMs while the cooled seats are on, thefeature will turn itself off and will need to be reactivated.Climate controlled s

To install a filter:1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing.2. Push in on the

Memory profilesThe memory feature also coordinates with user-created profile settingsutilizing the infotainment touchscreen system. See the Creating a

WARNING: To prevent possible damage to the seat or safetybelts, ensure that the safety belts are not buckled when movingthe seat to the load floor pos

Press and hold the controlmechanism to lower the seatback.The top portion lowers the right(40%) seatback, and the bottomportion lowers the left (60%)s

Seat-mounted armrest and cupholdersYour vehicle is equipped with a rearseat armrest. To fold the armrestdown, release the latch located onthe seatback

Rear heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes, spinal cord

SAFETY RESTRAINTSPersonal Safety System™The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupan

Solid illumination after the engine is started indicates the on-boarddiagnostics system (OBD-II) has detected a malfunction. Refer toOn-board diagnost

longitudinal deceleration. The pretensioners are designed to activate infrontal and near-frontal collisions, and in rollovers and side collisionswhen

WARNING: Always transport children 12 years old and under inthe back seat and always properly use appropriate childrestraints.The front passenger sens

The Restraints Control Module (RCM) monitors its own internal circuitsand the circuits for the airbag supplemental restraints, crash sensor(s),safety

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a seat belt.WARNING: Each seating position i

2. To unfasten, press the releasebutton and remove the tongue fromthe buckle.Restraint of pregnant womenWARNING: Always ride and drive with your seatb

(8 km/h) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers.In addition, the retractor is des

How to disengage the automatic locking modeDisconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic l

Safety belt extension assemblyIf the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can b

Second row comfort guideThe second row outboardlap/shoulder belt is equipped with abelt comfort guide. This guide isattached to the head restraint and

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected. Contact yourauthorized dealer as soon

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the onposition or less than1-2 minutes h

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...“Crashes are ra

One-time disableIf at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the Belt-Minder威 is

3. For the seating position being disabled, buckle then unbuckle thesafety belt three times at a moderate speed, ending in the unbuckledstate.• After

Important supplemental restraint system precautionsAirbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest cl

WARNING: Do not put anything on or over the airbag module.Placing objects on or over the airbag inflation area may causethose objects to be propelled

How does the safety belt pretensioner and airbag supplementalrestraint system work?The safety belt pretensioner andairbag SRS are designed to activate

WARNING: Several air bag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the air bag has deployed, the air bag

The front passenger sensing system will disable (will not inflate) thefront passenger’s frontal airbag if:• the front passenger seat is unoccupied, or

• When the front passenger sensing system enables the front passengerfrontal airbag (may inflate), the passenger airbag status indicator willilluminat

AdvanceTrac威 off light:Illuminates whenAdvanceTrac威/traction control hasbeen disabled by the driver. Refer tothe Driving chapter for moreinformation.L

WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushionand affect the decision of

If objects are lodged and/or cargo is interfering with the seat; please takethe following steps to remove the obstruction:• Pull the vehicle over.• Tu

If any of these things happen, even intermittently, have the supplementalrestraint system serviced at an authorized dealer immediately. Unlessserviced

The side airbag system consists ofthe following:• An inflatable bag (airbag) with agas generator concealed behindthe outboard bolster of the driverand

WARNING: If the sideairbag has deployed, theairbag will not function again.The side airbag system(including the seat) must beinspected and serviced by

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

How does the Safety Canopy姞 System work?The design and development of theSafety Canopy System includedrecommended testing proceduresthat were develope

The safety canopy is mounted to roof side-rail sheet metal, behind theheadliner, above each row of seats. In certain lateral collisions or rollovereve

Determining if the system is operationalThe SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Ref

Important child restraint precautionsWARNING: Always make sure your child is secured properly ina device that is appropriate for their height, age and

Door ajar (RTT): Displays whenthe ignition is on and any door isopen.Tailgate ajar (RTT): Displayswhen the ignition is on and thetrunk is open.Low was

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfantsor tod-dlersChildren weighing 40 l

Recommendations for attaching child safety restraints for childrenRe-straintTypeChildWeightUse any attachment method as indicated be-low by “X”LATCH(l

WARNING: Never let a passenger hold a child on his or her lapwhile the vehicle is moving. The passenger cannot protect thechild from injury in a colli

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle.If the child is the proper height, age, and weigh

position whenever possible. If all children cannot be seated andrestrained properly in a rear seating position, properly restrain thelargest child in

2. Pull down on the shoulder beltand then grasp the shoulder beltand lap belt together.3. While holding the shoulder andlap belt portions together, ro

5. To put the retractor in theautomatic locking mode, grasp theshoulder portion of the belt and pulldownward until all of the belt ispulled out.6. All

10. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the

Your vehicle has LATCH loweranchors for child seat installation atthe seating positions marked withthe child seat symbol.The LATCH anchors are located

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

Grade assist (RTT): Illuminateswhen the grade assist is turned on.Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ig

The rear seats of your vehicle are equipped with built-in tether strapanchors located behind the seats as described below.The tether anchors in your v

2. Locate the correct anchor behindthe gap cover for the selectedseating position.3. Clip the tether strap to theanchor as shown.WARNING: If the tethe

both the lap and shoulder belt on children who have outgrown childsafety seats, Ford Motor Company recommends use of a belt-positioningbooster.Booster

Types of booster seatsThere are generally two types of belt-positioning booster seats: backlessand high back. Always use booster seats in conjunction

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

NOTICE TO CROSSOVER VEHICLE OWNERSCrossover vehicles handle differentlythan passenger cars in the variousdriving conditions that areencountered on str

driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other t

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGTire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereappli

WARNING: The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydro

MESSAGE CENTERWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use ex

• Extra load: A class of P-metric or Metric tires designed to carry aheavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires].Increasing the

WARNING: Under-inflation is the most common cause of tirefailures and may result in severe tire cracking, tread separationor “blowout”, with unexpecte

Note: If you have to drive a distance to get air for your tire(s), checkand record the tire pressure first and add the appropriate air pressurewhen yo

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them

U.S. DOT Tire Identification Number (TIN)Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the s

WARNING: When mounting replacement tires and wheels, youshould not exceed the maximum pressure indicated on thesidewall of the tire to set the beads w

• Do not run over curbs or hit the tire against a curb when parkingWARNING: If your vehicle is stuck in snow, mud, sand, etc., donot rapidly spin the

• Front-wheel drive(FWD)/All-wheel drive (AWD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotating the ti

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Note: You may not find this information on all tires because it is notrequired by federal law.Letter rating Speed rating - mph (km/h)M 81 mph (130 km/

Press the OK button to selecthighlighted options and confirmchoices/messages.Main menuFrom the main menu screen you can choose the following:• Display

12. Treadwear, Traction and Temperature Grades• Treadwear: The treadwear grade is a comparative rating based on thewear rate of the tire when tested u

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

When your temporary spare tire is installedWhen one of your road tires needs to be replaced with the temporaryspare, the TPMS system will continue to

Low tirepressurewarninglightPossiblecauseCustomer action requiredFlashingwarning lightSparetire inuseYour temporary spare tire is in use. Repairthe da

SNOW TIRES AND CHAINSWARNING: Snow tires must be the same size, load index, speedrating as those originally provided by Ford. Use of any tire orwheel

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

Payload – is the combined weight of cargo and passengers that thevehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Lab

Seating and Safety Restraints 116Seating 116Safety restraints 129Airbags 143Child restraints 158Tires, Wheels and Loading 176Tire information 178Tire

Full analog tachometer + FuelgaugeFull analog tachometer + Fuelgauge + Engine coolanttemperature gaugeIntelligent all-wheel drive(AWD) (if equipped) +

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

Steps for determining the correct load limit:1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.

calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 -540 = -103 kg. You will need to reduce the load weight by at least240 lb. (104

For load specification terms found on the label, refer to Vehicle loading- with and without a trailer in this chapter. Remember to figure in thetongue

HitchesDo not use hitches that clamp onto the vehicle’s bumper or attach to theaxle. You must distribute the load in your trailer so that 10–15% of th

Driving while you towWhen towing a trailer:• Do not drive faster than 70 mph (113 km/h) during the first 500 miles(800 km) of trailer towing and don’t

RECREATIONAL TOWINGFollow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a motor hom

The selected gear will be displayedat the bottom of the vertical bartachometer (if selected).The selected gear will be displayedwithin the full analog

STARTINGIgnition modes1. Off — This position shuts the engine and all electrical accessories off.Press and release the START/STOP button without apply

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

• Make sure the gearshift lever is inP (Park).Push button start systemYour vehicle is equipped with thepush button start system. You canstart your veh

when you press the START/STOP button, it may be necessary to moveyour IA key to another area within the vehicle. The IA key may not bedetected near th

Absence of the Intelligent Access key: Once the vehicle has started,the vehicle will remain running until being turned off by theSTART/STOP button, ev

WARNING: To reduce the risk of electrical shock, do not useyour heater with ungrounded electrical systems or two-pronged(cheater) adapters.Prior to us

How to use the engine block heaterEnsure the receptacle terminals are clean and dry prior to use. To cleanthem, use a dry cloth.Depending on the type

Brake assistThe brake assist system provides full braking force during panic brakingsituations. It detects a rapid application of the brake pedal and

WARNING: Always set the parking brake fully and make surethat the gearshift is securely latched in P (Park). Turn theignition to the lock position and

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

• Average fuel economy — shows the average fuel economy for a giventrip.• Estimated amount of fuel consumed — shows the amount of fuel usedfor a given

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

Electronic stability control (ESC)Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for exa

Switching off AdvanceTrac威 with RSC威If the vehicle is stuck in snow, mud or sand, and seems to lose enginepower, switching off certain features of the

TRAILER SWAY CONTROLWhen properly equipped, trailer sway control will use the vehicle’sAdvanceTrac威 with RSC威 system to detect and help reduce trailer

STEERINGTo help prevent damage to the power steering system:• Never hold the steering wheel at its furthest turning points (until itstops) for more th

If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park):1. A

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D

Recommended shift speedsUpshift according to the following chart:Upshifts when accelerating(recommended for best fuel economy)Shift from:1 - 2 15 mph

Using hill start assistHill start assist is activated automatically when the vehicle is stopped ona slope greater than five degrees. Hill start assist

Fuel EconomyPress the right arrow on the left steering wheel mounted button whenfuel economy is selected. The boxes in the upper right corner of thesc

REVERSE SENSING SYSTEMThe reverse sensing system (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Reverse) is selec

The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to th

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rear video camera system,located on the liftgate, provides avideo image of the area behind thevehicle. It adds

Objects are getting closer to your vehicle as they move from the greenzone (4) to the yellow (3) or red zones (2). Use the side mirrors andrearview mi

When manual zoom is enabled, onlythe centerline will be shown.Rear camera delayAfter shifting out of R (Reverse) and into any gear other than P (Park)

Note: If the camera system image is not clear or seems distorted, it maybe covered with water droplets, snow, mud or any other substance. Ifthis occur

Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe system inspected by your authorized dealer.• If the image is not cle

OperationThe radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle.If the radar detects that yourvehicle is rapidly

WARNING: The collision warning system’s brake support canonly help reduce the speed at which a collision occurs if thedriver applies the vehicle’s bra

Note: If the system cannot be turned off in a MyKey™ equipped vehicle,refer to MyKey™ in the Locks and Security chapter for moreinformation.Note: If c

To determine your average highway fuel economy, do the following:1. Drive the vehicle at least 5 miles (8 km) with the speed controlsystem engaged to

WARNING: Objects in the blind spot mirror are closer than theyappear.BLIND SPOT INFORMATION SYSTEM (BLIS姞) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED)

becomes active. Afterwards, the BLIS威 remains active for all speedsincluding zero mph. BLIS威 is also active if the transmission is placed in N(Neutral

BLIS威 False AlertsDue to the nature of radar technology, there may be certain instanceswhen the BLIS威 will alert with no object present in the blind z

The CTA system detects vehicles approaching up to 45 feet (14 meters)away. Coverage decreases when vehicles and objects in close proximityblock the CT

CTA detection limitations: Due to the nature of radar technology,there may be certain instances where vehicles entering and exiting theblind spot zone

BLIS威 and/or CTA fault operationIf the BLIS威 and/or CTA senses a fault on either the left or right sensor,the BLIS威 alert indicator will go on and rem

The following table lists possible causes and actions for this messagebeing displayed:The surface of the radar isdirty or obstructed in somewayClean t

All components of the AWD system are sealed for life and require nomaintenance.Note: When an AWD system fault is present, the warning CHECK AWDwill di

Under severe operating conditions, the A/C may cycle on and off toprotect overheating of the engine.Basic operating principles• Drive slower in strong

WARNING: If the parking brake is fully released, but the brakewarning lamp remains illuminated, the brakes may not beworking properly. See your author

VehicleAutolamp Delay Off, 10 / 20 (default setting) / 30 / 60 / 90 / 120 /180 secondsEasy Entry/Exit On (default on key cycle) / OffFuel DTE Calculat

the system has cooled down, normal AWD function will return. Whendriving at slow speeds in deep sand under high outside temperatures,use L (Low) gear

Management in encouraging you to help preserve our national forest andother public and private lands by “treading lightly.”Driving on hilly or sloping

Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s

DRIVING THROUGH WATERIf driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive th

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Owner Guide portfolio in the glove compartment. In Canada, the card isfound in the Warranty Guide in the glove compartment.U.S. Ford, Mercury and Linc

WARNING: Failure to inspect and if necessary repair fuel leaksafter a collision may increase the risk of fire and serious injury.Ford Motor Company re

COLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge60A — — Blue Yellow Yellow70A — — Tan — Brown80A — — Natural Black B

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Driver front smart window2 15A Not used (spare)3 30A Passenger

Fuse/RelayLocationFuse AmpRatingProtected Circuits12 15A Interior lighting, Puddle lamps,Backlighting13 15A Right turn/stop lamps and turn signals14 1

*MyKeyCreate MyKey Press and hold OK to create MyKeyTraction Control Always On / User SelectableSpeed Warning Off, 65 mph (105 km/h), 55 mph (89 km/h)

Fuse/RelayLocationFuse AmpRatingProtected Circuits32 15A Moon roof, Power windows,Compass/auto-dimming rear view mirror33 10A Not used (spare)34 10A R

WARNING: To reduce risk of electrical shock, always replacethe cover to the power distribution box before reconnecting thebattery or refilling fluid r

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description12 — Not used13 — Starter relay14 — Not used15 — Fuel pump relay16 — Not used17 — No

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description41 — Not used42 30A** Passenger seat43 30A** ABS valves44 — Rear washer relay45 5A*

Fuse/RelayLocationFuse AmpRatingPower Distribution Box Description71 — Not used72 — Not used73 — Not used74 — Not used75 — A/C clutch diode76 — Not us

CHANGING THE TIRESIf you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel thatis different in brand, size or appearance from the road tires and wheelsand

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following:• Handling, stability and braking performance• Comfort and

Removing the spare tire and jack1. Lift the carpeted load floor panellocated in the rear of the vehicle.2. Remove the spare tire cover (ifequipped).3.

WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h

System Check*Oil LifeWash FluidDoorsLiftgateB lind spotCross TrafficBrakesFuel (distance to empty)*Some items will only display during a system check

3. Align the slot on top of the jackwith the sheet metal flangeindicated by the jack locator trianglenext to the tire you are changing.Turn the jack h

If you are stowing a flat 22 inch tire and wheel assembly,temporarily remove the load floor, plastic stowage bins (if equipped), andthe foam load floo

Note: Inspect the wheel pilot holeprior to installation. If there isvisible corrosion in wheel pilot hole,remove loose particles by wipingwith clean r

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery.2. Connect the other end of thepositive (+) cable to the

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.Note: In the illustration, the vehicle on the bottom i

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

If the vehicle is towed by other means or incorrectly, vehicledamage may occur.Ford Motor Company produces a towing manual for all authorized towtruck

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizedFord, Lincoln, or Mercury dealer. While any authorized

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

LIFTGATE AJAR — Displayed when the liftgate is not completelyclosed.PASSENGER DOOR AJAR — Displayed when the passenger door isnot completely closed.RE

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

LINE before exercising rights or seeking remedies created by the FederalMagnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you chooseto seek r

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean. In Canada, useMotorcraft Engine Sh

may cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips:• The winds

engine oil in the Maintenance and Specifications chapter. If thewarning stays on or continues to come on, contact your authorizeddealer as soon as pos

• Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to a

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat

• Clean spills as quickly as possible.• Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather.•

FORD AND LINCOLN MERCURY CAR CARE PRODUCTSYour Ford or Lincoln Mercury authorized dealer has many qualityproducts available to clean your vehicle and

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column.2. Go to th

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT1. Engine coolant reservoir2. Power steering fluid reservoir3. Brake fluid reservoir4. Battery5. Power

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice

4. Open the hood. Protect yourself from engine heat.5. Locate and carefully remove the engine oil level dipstick.6. Wipe the dipstick clean. Insertthe

Maintenance and Specifications 294Engine compartment 296Engine oil 298Battery 301Engine coolant 304Fuel information 309Air filter(s) 324Part numbers 3

message after driving a short distance with the road tire re-installed orafter the system is allowed to cool.CHECK AWD — Displayed in conjunction with

• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the enginewith oil. Oil levels above thismark

Use SAE 5W-20 engine oilOnly use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol confo

If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced.For longer, trouble-free operation, keep

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe bat

ENGINE COOLANTChecking engine coolantThe concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance i

Adding engine coolantWhen adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservo

a coolant degas system with a pressurized cap, or if it is necessary toremove the coolant pressure relief cap on the radiator of a vehicle withan over

Recycled engine coolantFord Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet avai

Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engin

4. Check the coolant level and replenish if low.WARNING: Fail-safe mode is for use during emergencies only.Operate the vehicle in fail-safe mode only

COULD NOT PROGRAM KEY — Displayed when an attempt is madeto program a spare key using two existing MyKeys. Refer to MyKey™ inthe Locks and Security ch

WARNING: Gasoline may contain benzene, which is acancer-causing agent.Observe the following guidelines when handling automotive fuel:• Extinguish all

WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel co

2. Open the fuel filler door.3. Slowly insert the fuel filler nozzle fully into the fuel system and leavethe nozzle fully inserted until you are done

Note: Use of any fuel other than those recommended may causepowertrain damage, a loss of vehicle performance, and repairs may notbe covered under warr

Running out of fuelAvoid running out of fuel because this situation may have an adverseeffect on powertrain components.If you have run out of fuel:• Y

1. After lifting the trunk cargocover, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment.2. Slowly in

Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the M

Calculation 2: Multiply liters used by 100, then divide by totalkilometers traveled.Keep a record for at least one month and record the type of drivin

• Use recommended engine oil. Refer to Maintenance productspecifications and capacities in this chapter.• Perform all regularly scheduled maintenance

If other than Ford, Motorcraft威 or Ford-authorized parts are used formaintenance replacements or for service of components affectingemission control,

STARTING SYSTEM FAULT — This message is displayed when thereis a problem with your vehicle’s starting security system; your vehiclewill not be able to

2. Poor fuel quality or water in the fuel—the engine may misfire or runpoorly.3. The fuel fill inlet may not have been properly closed. See Easy Fuel™

The OBD-II system is designed to check the emission control systemduring normal driving. A complete check may take several days. If thevehicle is not

BRAKE FLUIDThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX

5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartmentin this

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage.If necessary, add fluid in 1/2 pint(250 ml) increme

housing and cover. This could cause filter damage and allow unfilteredair to enter the engine if not properly seated.6. Replace the air filter housing

• Lubricate all hood, door and trunk lid hinges, and latches with a lightgrade oil. See the Cleaning chapter for more information.• Cover interior tri

Tires• Maintain recommended air pressure.Miscellaneous• Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to preven

MOTORCRAFT PART NUMBERSComponent 3.7L V6 engineEngine air filter element FA-1884Battery BXT-65Oil filter FL-500-SSpark plugs SP-52011Refer to schedule

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem Capacity Ford Part NameFord Part Number /Ford SpecificationBrake fluidBetween MIN andMAX on rese

BLINDSPOT NOT AVAILABLE SENSOR BLOCKED SEEMANUAL(if equipped) — Displayed when the blind spot informationsystem/cross traffic alert system sensors are

Item Capacity Ford Part NameFord Part Number /Ford SpecificationEngine oil15.5 quarts (5.2L)•Motorcraft威 SAE 5W-20Premium Synthetic BlendMotor Oil (US

Item Capacity Ford Part NameFord Part Number /Ford SpecificationPower Transfer Unit(PTU) fluid (AWD)512 ounces (0.35L)Motorcraft威 SAE 75W-140Synthetic

ENGINE DATAEngine 3.7L V6 engineCubic inches 226Required fuel 87 octaneFiring order 1–4–2–5–3–6Ignition system Coil on plugCompression ratio 10.3:1Spa

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

LINCOLN CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Lincoln Custom Accessories are available for yourvehicle through your local Lincoln or

Peace of mind•Remote start •Vehicle tracking and recovery*•Keyless entry keypad •Protective seat covers*•Cargo security shade •Windshield wiper shaker

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford, Lincoln, and Mercury owners have discoveredthe powerful protection of Ford ESP.

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3392011 MKX (mkx)Owners Guide, 1st PrintingUSA (fus)

TO STOP ALARM START VEHICLE — Displayed when the perimeteralarm system is armed and the vehicle is entered using the key on thedriver’s side door. In

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

If your message center is prematurely reset or becomes inoperative, youshould perform the oil change interval at six months or 5,000 miles(8,000 km) f

Genuine Ford parts and serviceWhen planning your maintenance services, consider your Ford andLincoln Mercury dealership for all your vehicle’s needs.G

WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW?Owner checks and servicesCertain basic maintenance checks and inspections should be performedby the owner

Multi-point inspectionIn order to keep your vehicle running right, it is important to have thesystems on your vehicle checked regularly. This can help

Scheduled Maintenance Guide3462011 MKX (mkx)Owners Guide, 1st PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGFor your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service

Oil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire wear and measuretread depth

Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (5,000 km) of theOIL CHANGE REQUI

MYLINCOLN TOUCH™WARNING: Driving while distracted can result in loss of vehiclecontrol, accident and injury. Ford strongly recommends thatdrivers use

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATIO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

SPECIAL OPERATING CONDITIONSIf you operate your Ford/Lincoln/Mercury vehicle primarily in one of themore demanding Special Operating Conditions listed

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryAs required – Chang

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped).– Replace e

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VA

DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOUR

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

COOLANT CHANGE RECORDEngine coolant❑6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first).❑After initial change - change cool

DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEMWITH MYTEMPNote: Your climate control system is touch sensitive. You need onlylightly touch the contro

Engine coolant change logDEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DATE:MILEAGE:DEALER VALIDATI

AAccessory delay ...65Adaptive Cruise Control ...69AdvanceTrac ...218Air cleaner filter ..

recommendations ...161Child safety seats - boosterseats ...172Cleaning your vehicleengine comp

dipstick ...298filter, specifications ...300, 328recommendations ...300refill capacities ...

Instrument panelcleaning ...289cluster ...12lighting up panel andinterior ...

Parts(see Motorcraft威 parts) ...328Passenger OccupantClassification Sensor ...130Power distribution box(see Fuses) ...

SecuriCode keyless entrysystem ...110SecuriLock passive anti-theftsystem ...

WWarning lights (see Lights) ...12Washer fluid ...297Water, Driving through ...253Windowspower ...

economical and efficient. Recirculated air may also help reduceundesirable odors from entering the vehicle. Touch MAX A/C again fornormal A/C operatio

Operating tips• To reduce fog build-up on the windshield during humid weather,select(defrost) or (floor/defrost).• To reduce humidity build-up inside

Touchscreen featuresPress the lower right corner on the touchscreen to access these features.1.(Power): Press to activate/deactivate the climate contr

CONGRATULATIONSCongratulations on acquiring your new Lincoln. Please take the time toget well acquainted with your vehicle by reading this handbook. T

5. MAX A/C: Press to distribute recirculated air through the instrumentpanel vents to cool the vehicle. This is more economical and efficientthan norm

• Press to control the heated seat. Refer to Heated and cooledseats in the Seat and Safety Restraints chapter.• Pressto control the cooled seat. Refer

*Note: If you have said “Temperature”, you can then say any of thefollowing commands:• High • Low• <15.5–29.5> degrees • <60–85> degreesFo

Automatic climate controlFor hot weather conditions:• The interior cabin will be cooled to 72°F (22°C).• The cooled seats (if equipped) will be set to

HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Adapti

Autolamp controlThe autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control.

Fog lamp controlThe fog lamps can be turned onwhen the headlamp control is inthe, ,or positionsand the high beams are not turnedon.Press the top of th

WARNING: Always remember to turn on your headlamps atdusk or during inclement weather. The Daytime Running Lamp(DRL) system does not activate the tail

Vertical aim adjustment1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away.• (1) 8 fe

4. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver, turn the adjuster eitherclockwise (to adjust down) orcounterclockwise

Protecting the environmentWe must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning a

INTERIOR LAMPSFront row map lamps (if equipped)To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when:• an

BULB REPLACEMENTLamp assembly condensationExterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product

FunctionNumber ofBulbsTradeNumber* Rear sidemarker lamp N/A LED* Stop/tail/turn lamp N/A LEDBackup lamp 2 921License plate lamp 2 C5W* High-mount brak

4. Turn the bulb holdercounterclockwise and remove it.5. Disconnect the electricalconnector.WARNING: Handle a halogen headlamp bulb carefully and keep

2. At the wheel well, remove thefasteners from the splash shield,then pull the splash shield back togain access to the bulbs.3. Rotate the bulb socket

Replacing backup lamp bulbsThe backup lamp bulb is located in the lower portion of the tail lampassembly. Follow the below steps to replace the bulb.N

Replacing license plate lamp bulbs1. Make sure the headlamp switch isin the off position.2. Remove the two screws and thelicense plate lamp assembly f

WINDSHIELD WIPERSWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespe

Windshield washer: Press the endof the stalk:• briefly: causes a single swipe ofthe wipers without washer fluid.• a quick press and hold: thewipers wi

From either position, the control will automatically return to the 2 or O(off) position.Reverse wiper feature: The rear wiper will be automatically ac

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.WARNING: Please read the section Airbag Supple

Easy entry/exit featureWhen the ignition is turned off, the column will move to the full up andin position if this feature is activated through the me

ILLUMINATED VISOR MIRRORLift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureThe visor will slide back and forthon the rod for in

CENTER CONSOLEYour vehicle may be equipped with a variety of console features. Theseinclude:1. Cupholders2. Utility compartment with in-binpower point

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

To operate one-touch up, pull the switch completely up to the seconddetent and release quickly. The window will close fully. Momentarilypress the swit

Window lockThe window lock feature allows onlythe driver and front passenger tooperate the power windows.To lock out all the window controls(except fo

EXTERIOR MIRRORSPower side view mirrorsWARNING: Do not adjust the mirror while the vehicle is inmotion.To adjust your mirrors:1. Rotate the control cl

Fold-away mirrorsPull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash.Blind spot mirrors (if equipped)Your

2. Accelerate to the desired speed.3. Press SET upward and release.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument

Turning off speed controlTo turn off the speed control, press OFF downward or turn off theignition.Note: When you turn off the speed control or the ig

authorized service facilities, and that the diagnostic information may beused for any purpose. See your SYNC威 supplement for more information.Event Da

WARNING: Do not use in poor visibility, specifically fog, rain,spray or snow.Using adaptive cruise controlNote: It is the drivers responsibility to st

Following a vehicleWARNING: When following a vehicle in front of you, the vehiclewill not decelerate automatically to a stop, nor will the vehiclealwa

Setting the gap distanceThe distance between your vehicleand the vehicle in front of you canbe decreased or increased bypressing the GAP control up or

Changing the set speedThere are three ways to change the set speed:• Accelerate or brake to the desired speed and press SET upward andrelease.• Increa

Detection issuesThe radar sensor has a limited field of vision. In some situations it maynot detect vehicles at all or detect a vehicle later than exp

• There may be issues with the detection of vehicles in front whendriving into and coming out of a bend or curve in the road.In these cases ACC may br

Cause ActionThe surface of the radar in thegrille is dirty or obstructed insome wayClean the grille surface in front ofthe radar or remove the objectc

STEERING WHEEL CONTROLSAudio control featuresSEEK: Press up or down to selectthe next/previous radio stationpreset, CD track or satellite radiochannel

• Phone• Redundant center stack display• Favorite contacts• Climate• On• Fan speed• TemperaturePANORAMIC VISTA ROOF™ AND POWER SUNSHADES(IF EQUIPPED)T

To open power sunshades andpanoramic Vista Roof™: Pressand release thecontrol toopen the sunshade. The front andrear sunshades open simultaneously.Not

To read data recorded by an EDR, special equipment is required,and access to the vehicle or the EDR is needed. In addition to thevehicle manufacturer,

HomeLink姞 Wireless Control System (if equipped)The HomeLink威 Wireless ControlSystem, located on the driver’s visor,provides a convenient way toreplace

1. Position the end of yourhand-held transmitter 1–3 inches(2–8 cm) away from the HomeLink威button you wish to program (locatedon your visor) while kee

Gate Operator & Canadian ProgrammingDuring programming, yourhand-held transmitter mayautomatically stop transmitting —not allowing enough time for

Erasing HomeLink姞 buttonsTo erase the three programmedbuttons (individual buttons cannotbe erased):• Press and hold the two outerHomeLink威 buttons unt

Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot int

Note: Cycling the ignition prior to completely latching the liftgate couldresult in damage to the liftgate and/or its power components. Make surethe l

To power open the liftgate withoutside liftgate control button:1. Unlock the liftgate with thetransmitter or power door unlockcontrol. If the intellig

Obstacle detection:The power liftgate system is equipped with an obstacle detection feature.If the power liftgate is closing, the system will reverse

Manual liftgate operationThe liftgate cargo area is only intended for cargo, not for passengers.To open the liftgate, press thebutton located in the t

CARGO AREA FEATURESCargo management system (if equipped)The cargo management systemconsists of storage compartmentslocated in the floor of the rear ca

CELL PHONE USEThe use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,dri

Utility hookThe utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 lb (4.5 kg) on the hook.ROOF RACK SYSTEM

INTELLIGENT ACCESS KEY (IA KEY)Your vehicle is equipped with twointelligent access keys whichoperate the power locks and theremote entry system. The I

feature. When the MyKey™ feature is enabled the user can use systemcheck in the message center to see how many MyKeys™ and admin keysare programmed to

MyKey™ is successfully programmed. Make sure you label it so you candistinguish it from the admin keys. Note: To program the optionalsettings go to St

Refer to Message center in the Instrument Cluster chapter for MyKey™system warnings displays.Using MyKey™ with remote start systemsMyKey™ is not compa

TroubleshootingCondition Potential CausesCan’t create aMyKey™• Key in backup slot is the last remaining adminkey (there always has to be at least one

Condition Potential CausesI accidentallyprogrammed all keysas MyKeys™• Vehicle has a non Ford-approved remote startsystem that is recognized as an adm

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Smart unlocksThe smart unlock feature is intended to prevent

Autolock featureThe autolock feature will lock all the doors when:• all the doors are closed,• the ignition on,• you shift into any gear putting the v

1. Turn the ignition on.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn the ignition off.4. Press the power door unlockcont